Page 8 of 10

Re: The SDB ARTEMIS air rifle

Posted: Tue Jun 12, 2018 7:01 pm
by sagar 12345
thank you for reply basuda & bullo oka

Importing optics for airguns

Posted: Tue Jun 12, 2018 10:23 pm
by T.Chalukumba Ao
Dear members kindly advise me import optics like rifle scopes eye from aboard.Vortex..leupold..Burris.. Nikon ete

Re: Importing optics for airguns

Posted: Wed Jun 13, 2018 8:52 am
by Bullo oka
T.Chalukumba Ao wrote:Dear members kindly advise me import optics like rifle scopes eye from aboard.Vortex..leupold..Burris.. Nikon ete
Dear T.Chalukumba Ao,
That isn't possible, you may try your luck on cheaper ones.

Sent from my ONEPLUS A5000 using Tapatalk

Re: The SDB ARTEMIS air rifle

Posted: Wed Jun 13, 2018 8:53 am
by targetpoint
Try to contact Rijo Joseph.He is only reliable source of quality original air gun rated scope as far as I know.
Thanks.

Re: The SDB ARTEMIS air rifle

Posted: Thu Jun 14, 2018 9:15 am
by vpillai
targetpoint wrote:Try to contact Rijo Joseph.He is only reliable source of quality original air gun rated scope as far as I know.
Thanks.
Dear Target point,you have contact details for Mr.Rijo Joseph to check for scopes, thanks

Sent from my SM-G925I using Tapatalk

Re: The SDB ARTEMIS air rifle

Posted: Thu Jun 14, 2018 10:13 am
by guru050
vsraja wrote:you should remove the trigger pin first and remove the trigger out. Then only you should remove the last pin with the help of a spring compressor.I think you have removed the last pin first.

Added in 2 minutes 8 seconds:
guru050 wrote:
sagar 12345 wrote:HI I HAVE BOUGHT SDB ARTEMIS 0.177 CAL. AIR RIFLE SIX MONTH BEFORE FROM KOVIBAZZAR.COM . SINCE IT IS FACTORY TUNED WITH MOLY GREASE BUT STILL I WANT TO TUNE IT WITH PRECIHOLE MOLY 60%. UP TO DATE ALMOST 2000 PELLETS FIRED. MY PROBLEM IS THAT I DONT KNOW HOW TO REMOVE TRIGGER CAN EXPERTS LIKE BASUDA ,GNV SIR TELL ME .
Dear sagar 12345,

This rifle trigger is simple one piece, you just need to remove two pins from back of a Tube which holding piston components and trigger. Pic is attached for reference.
Be careful while removing pins from this tube because it contains compressed spring.
hi guru050. I think you have reduced some preload from the artemis spring.How is the performance now?
Dear vsraja,

I have changed the piston seal not the preload from the spring. Performance of this gun is best, accurate and powerful.

Thank You.

Re: The SDB ARTEMIS air rifle

Posted: Thu Jun 14, 2018 10:56 am
by targetpoint
Dear vpillai,
Sorry I don't have his contact details but some of our senior members can help you in this matter.
Thanks.
Shoot Less But Shoot Class.

Re: The SDB ARTEMIS air rifle

Posted: Thu Jun 14, 2018 12:00 pm
by vpillai
targetpoint wrote:Dear vpillai,
Sorry I don't have his contact details but some of our senior members can help you in this matter.
Thanks.
Shoot Less But Shoot Class.
Dear,thanks a lot

Sent from my SM-G925I using Tapatalk

Re: The SDB ARTEMIS air rifle

Posted: Sun Jun 24, 2018 10:15 am
by sagar 12345
today i disassemble artemis air rifle for proper lubrication with precihole moly grease 60%.i found main spring is canted. i cleaned piston ,spring ,spring guide & lubricate them with moly grease & reassemble it. there is very less preload in artemis as compair to huricaine. reassemble trigger is very hard procidure . it is not easy to allin trigger hole with cylinder hole & insert trigger pin it takes me about hours. finally i did it but i will never try this again .after lubrication gun becomes very smooth ,cocking effort is also reduced. seniors please can you tell me easy procidure to allign trigger pin.

Re: The SDB ARTEMIS air rifle

Posted: Sun Jun 24, 2018 11:19 pm
by Basu
Reassembling the trigger is little tricky.
Load the spring first in the trigger hole then put the other end into the trigger housing.
Then push the trigger up into the slot.
Align the holes by inserting one pin and then put the original pin into the hole from other end.
A video could be useful but can't help.

Basu

Re: The SDB ARTEMIS air rifle

Posted: Mon Jun 25, 2018 7:24 am
by vsraja
Push the trigger pin with one hand and try to align the trigger by another hand.First ensure that the trigger pin can enter the hole without any difficulty.

Sent from my SM-G610F using Tapatalk

Re: The SDB ARTEMIS air rifle

Posted: Mon Jun 25, 2018 8:27 am
by targetpoint
First put the trigger inside as far as it can reach.Then light a torch on other side of hole opposite to you.Look through the hole.When the trigger hole perfectly aligned with hole of cylinder it should be perfect circle not oval.Then keeping the trigger in same position with one hand slowly push the pin as far as it can go.Then use mallet for it.
It is better to grease the pin slightly for easy installation.
Never hammer hit hard until you perfectly align it.The installation of trigger pin doesn't require much force.
Thanks.
Shoot Less But Shoot Class.

Re: The SDB ARTEMIS air rifle

Posted: Wed Jun 27, 2018 4:05 pm
by sagar 12345
can we fit precihole piston seal in artemis air rifle . i ask this queition because it is best fitted in huricaine &it is costing just rs.35.

Re: The SDB ARTEMIS air rifle

Posted: Wed Jun 27, 2018 5:13 pm
by targetpoint
Precihole piston seal is bit larger than Artemis piston seal because both have different compression cylinder diameter.Moreover Artemis piston seal is good in quality and much durable so no need of installing precihole seal.However if you want to install precihole piston seal then you have to resize the seal very carefully because there is a risk of damage.

Re: The SDB ARTEMIS air rifle

Posted: Fri Jun 29, 2018 3:23 pm
by sagar 12345
thank you targetpoint for your quick response