Indians For Guns

airgunner123 wrote:http://www.ebay.in/itm/Rifle-Telescope- ... SwhcJWOdww
http://www.ebay.in/itm/Rifle-Telescope- ... SwnOJWEzj6
are busnell scopes springer rated?

Some are, but the ones you have posted are almost certainly neither original Bushnell, nor springer rated!

hmm...alipress.com has cheap scopes but i read it frequently gets detained at customs...seems too risky...

does anyone sell this scope at lesser price?

how can i contact mr rijo joseph?

airgunner123 wrote:how can i contact mr rijo joseph?

Complete your mandatory posts to get PM activated. Not correct to share personal details in the public forum.


Sent from my iPad using Tapatalk

I ordered from AliExpress but it was held and sent back by Delhi custom , thank God I got my full refund ,I ordered second time from AliExpress and but it crossed custom and I received it in 22 days . It was Bushnell copy works well specification of scope R 3-9×40 with 11 MM mount

Sent from my LS-5015 using Tapatalk

Hello friends
I bought a nx 100 polaris few months back and its doing very well

Sent from my GT-I9082 using Tapatalk

Now I ordered a scope of 4×20 from shop clues with an 11 mm..can anyone tell me whether its ok or not for a nx 100

Sent from my GT-I9082 using Tapatalk

Most likely it won't work on a springer or NP piston air rifle.

The claws of scope may hold the groove but there is every possiblity that it would slide backward.
4x20 Chinese scopes are not meant for long range shooting.
You will find rainbow colors and has limited clarity.
I have mounted the same on my GenNex and gives me good service till 25 yds.

Basu

Ya there is slide back means creep but u can do many things to prevent it best is to modify the mount and install a pin so that it fits in a hole. But it is not easy to do that it need drill ,I cut a drill bit and installed it on scope mount and beneath it a little spring from a ball pen or any other little spring U can get posting pic hope it is helpful [img]https://uploads.tapatalk-cdn.com/201707 ... af55a2.jpg[/img]

Sent from my LS-5015 using Tapatalk

Hello Pravin

This is quite old, but have bought a scope myself recently. I believe the marketing team selling the scope are not adequately informed. That is an NCStar Rangefinder Reticle and it comes in MOA measurements in increments of 1. And 1 MilDot is roughly 3.5x 1 MOA at the same distance ie 100 yds. I was trying to figure out for a long time what those descending bars are meant for.

Those dashes represent increasing ranges of 25 yds from 100 to 225 for a target of width 18 inches (that is an average human shoulder to shoulder distance). Hence completely useless for an air gun

Looks pretty fancy though....hehe

Correction.....the MOA measurements have a spacing of 5 MOA between them.

Regards,

Basu wrote:The claws of scope may hold the groove but there is every possiblity that it would slide backward.
4x20 Chinese scopes are not meant for long range shooting.
You will find rainbow colors and has limited clarity.
I have mounted the same on my GenNex and gives me good service till 25 yds.

Basu

Dear Basu-da,

You mentioned fixing scope mounts with M-Seal (am not able to find that post again so unable to quote). Sir can you please show us a pic of the final jugaad. Planning to do the same in my case (have to adjust after every 20-25 shots). Did you apply the seal between the mounts and the barrel? Or just behind the mounts on the barrel. Thanks in advance....

Sir, I also stay in Saltlake Kolkata (Purbachal, cluster 3R just beside Stadium and Hyatt Regency). Currently am in New Delhi pursuing my final attempt at UPSC (hope to become a cop someday, hence interested in shooting). Hope to meet you someday and extract valuable advice from you sir.

Regrds,
Arnab Biswas

Dear Arnab,

Which gun do you have ?
I used the M seal as scope stop on scope rail.
Scope rail was made of MS and welded on the body of receiver.
This worked well on rail.
But it can not work on scope groove cut on receiver.

Basu